Generators

Sizing a Briggs & Stratton Standby Generator in Houston

November 7, 20267 min read
By Solivance Electric
Not sure what size you need? Use our free Houston generator size calculator

Solivance Electric is an authorized Briggs & Stratton standby generator dealer. That means a Houston homeowner or business owner can buy the generator from us, have us install it, or both. Before either happens, the unit has to be sized. A generator that is too small trips off the first time the AC compressor starts. A generator that is too large costs more than it needs to and runs lightly loaded for its whole life.

This post covers how Solivance Electric sizes a standby generator for a house in Bellaire or a strip center in Stafford, what goes into the number, and what to have ready before the site walk.

How do you size a standby generator for a Houston home?

A standby generator is sized from a load calculation, not from square footage. Solivance Electric lists every load you want running during an outage, totals the running watts, then adds the start-up surge of the largest motor — almost always the AC compressor. The generator has to carry the running load and survive that surge without the voltage collapsing.

That is the short answer. The rest of this post is the long one.

What goes into the load calculation?

The NEC gives two sizing paths for an optional standby system under Article 702. Either the generator carries every load the transfer switch can connect, calculated per NEC 220, or the install uses automatic load management so the generator never sees more than it can carry. Both are legal. The second is how a smaller unit covers a larger house.

On the site walk, Solivance Electric records:

  • Service size. 100A, 150A, 200A, or 400A (often a 320A meter base with two 200A panels).
  • AC equipment. Number of systems, tonnage, and the nameplate data on each condenser.
  • Heating. Gas furnace or electric heat strips. Heat strips are a large resistive load and matter in a freeze.
  • Large appliances. Electric range, electric dryer, electric water heater, pool pump, well pump, EV charger.
  • Must-run loads. Refrigerators, freezers, medical equipment, sump pumps, network gear, security.
  • Fuel. Natural gas meter size and location, or room for a propane tank.

The math under the hood is simple. Watts equal volts times amps. A 240V load drawing 20A is 4,800 watts, or 4.8 kW. Add up what will run at the same time, and the total is the running load.

Why does the air conditioner drive the size?

In Houston, the AC is the load that decides the generator. A compressor draws several times its running current for the first fraction of a second as it starts — the locked-rotor current on the nameplate. A generator has to supply that surge while everything else is already running.

Two houses with the same square footage can need very different generators:

FactorPushes the size upPulls the size down
AC systemsTwo or three condensers that can start togetherOne system, or a soft starter on the compressor
HeatingElectric heat stripsGas furnace
AppliancesElectric range, dryer, water heaterGas appliances
Load managementNone — every load at onceLoad-shed modules that hold back big loads
CoverageWhole-homeEssential-circuit subpanel

A soft starter on the compressor lowers the start-up surge. Load-shed modules let the transfer switch drop a second AC or the dryer when the generator gets close to its limit. Both are common ways to fit a right-sized generator to a Houston house with heavy cooling.

What about sizing for a business?

Commercial sizing follows the same logic with different loads. Walk-in coolers, POS systems, server closets, rooftop units, and lighting are the usual list. Three-phase service changes the math, and a business often has to decide which loads go on standby and which ride out the outage. We covered the commercial side in backup generators for Houston businesses. Retail and restaurant work in Stafford, Missouri City, and Sugar Land runs through our commercial center crew.

Does the electrical service need work first?

Sometimes. A standby generator connects through an automatic transfer switch at or near the service. If the service is 200A with room in the panel, the install is usually straightforward. If the house still runs on a 100A or 150A service, the panel is full, or the panel is a brand with a known failure history, the generator quote may include a panel upgrade.

The 2023 NEC also requires an outdoor emergency disconnect for one- and two-family dwellings under NEC 230.85. Many service-rated transfer switches satisfy that requirement when they are mounted outside. Solivance Electric confirms how the disconnect is handled during the site walk.

Natural gas or propane?

Most homes in Meyerland, West U, the Heights, and the Memorial Villages already have natural gas. A standby generator usually runs on it, but the gas meter has to supply the generator plus the furnace, water heater, and range at the same time. If the meter is too small, CenterPoint can upsize it. Solivance Electric includes that coordination in the install scope.

Homes without natural gas — some lots in Katy, Cypress, and rural Fort Bend — run the generator on propane from a tank on site. Tank size sets how long the generator runs between fills.

What does buying through an authorized dealer change?

Buying from an authorized dealer means the unit comes through the manufacturer’s channel and the install is registered. Warranty terms vary by model; Solivance Electric registers the install as an authorized dealer. You can see the current Briggs & Stratton lineup and pricing on our generators page. Call or request a quote to buy the unit alone or with a full install.

What should I have ready for the site walk?

The site walk goes faster when a few things are on hand. None of them are required, but each one shortens the list of follow-up questions.

  • A recent electric bill and gas bill, so the service and gas meter are easy to identify with CenterPoint.
  • A list of what has to run in an outage: whole home, or a short list of essential circuits.
  • Any medical equipment that needs power, with its plug type and rating.
  • Planned loads in the next few years — an EV charger, a pool, an added AC system, a garage apartment.
  • HOA rules on equipment placement and screening, if the neighborhood has them.

Planned loads matter most. A generator sized for the house today can come up short once a Level 2 charger or a second condenser goes in. Solivance Electric sizes for what is coming, not only for what is there.

What happens after the site walk?

  1. Load calculation. Solivance Electric totals the loads and picks a generator size with headroom.
  2. Fixed-fee quote. One number in writing covering the unit, transfer switch, pad, wiring, gas coordination, permits, and commissioning.
  3. Permits. We pull the electrical permit with the City of Houston or the local AHJ, and coordinate the gas side.
  4. Install and inspection. The generator is set, wired, tested under load, and inspected.
  5. Walkthrough. You see the transfer switch run a test transfer before we leave.

Our full generator install page covers the install in more detail, and the Bellaire page covers HOA and lot-line issues common inside the Loop.

Ready to size a generator?

Solivance Electric runs a free site walk, sizes the generator from your actual loads, and hands back a fixed-fee quote. Request a site walk or call (832) 965-9964. Financing available through Synchrony — ask about monthly payment options. Subject to credit approval. Details are on the financing page.

Walk a site. Get a number.

Solivance Electric LLC works Southwest Houston, the Heights, Bellaire, and the Memorial Villages from the shop at 13035 S Post Oak Rd Suite I, 77045 — greater Houston on a call. Panel upgrades, standby generators, EV chargers, parking-lot lighting, warehouse electrical. Call or request a quote online — licensed electrician on the phone, not a scheduler.

Synchrony

Financing available through Synchrony. Ask about monthly payment options. Subject to credit approval.

Solivance Care Plans

Yearly inspection, priority scheduling, member pricing on repairs.